By The RigArmor Team · Last reviewed: 25 October 2026
Short answer: The hierarchy of controls ranks ways to reduce workplace risk from most to least effective: elimination, substitution, engineering controls, administrative controls and personal protective equipment (PPE). Singapore's Code of Practice on WSH Risk Management asks employers to consider them in that order. It says a combination of controls is generally more effective, with PPE as the last resort.
A common risk assessment mistake is to jump straight to "wear gloves" or "issue PPE" and call the hazard controlled. That's the bottom of the list, not the top. This guide is for WSH officers, supervisors and anyone writing a risk assessment in Singapore. It explains the 5 levels, gives Singapore workplace examples and shows where PPE and workwear fit.
What is the hierarchy of controls?
The hierarchy of controls is an order of preference for controlling a hazard. You start with the measure that removes the hazard. You move down to measures that rely on people only as far as needed, often combining them with higher controls.
In Singapore, the WSH Council's Code of Practice on WSH Risk Management calls it the "Hierarchy of Control". Section 6.6.1 says: "Selection of risk control measures should be based on the Hierarchy of Control." Elimination comes first, "where practicable". Then, in the recommended order, come substitution, engineering controls, administrative controls and PPE.
It's the third step of a risk assessment. MOM's risk management page lists three basic steps: hazard identification, risk evaluation and risk control. For risk control, it says to "select control measures based on the principles of Hierarchy of Control."
You'll also see it called the risk control hierarchy or the hierarchy of hazard control. They mean the same thing.
Is the hierarchy of controls required in Singapore?
Under the WSH (Risk Management) Regulations, employers, self-employed persons, principals and platform operators must conduct a risk assessment. Regulation 4 requires them to take all reasonably practicable steps to eliminate foreseeable risks. Where that isn't reasonably practicable, they must put in place measures to minimise the risk, plus safe work procedures. Those measures may include substitution, engineering control, administrative control and suitable PPE.
The Code of Practice sets out the order to consider them in (section 4.2.2.3). Your WSH officer can tell you how this applies to your site.
The 5 levels, from most to least effective
The 5 levels of the hierarchy of control are elimination, substitution, engineering controls, administrative controls and PPE. The Code says a control higher up "is often more effective as the risk is reduced at or close to the source" (section 6.6.2.2).
Elimination
Elimination: removing the hazard, so nobody is exposed to it. The Code calls it "a permanent solution" that "should be attempted first". The Code's own example: "sharp edges can be eliminated in a store or work area" (Appendix C).
Substitution
Substitution: replacing a hazardous material, process or piece of equipment with a less hazardous one. The Code's own example is "using water-based paint instead of solvent-based paint". On a cleaning job, it could mean switching to a less hazardous chemical that still does the job.
Engineering controls
Engineering controls: physical changes to the workplace, equipment or process that separate people from the hazard. The Risk Management Regulations list examples such as a barrier, enclosure, guarding, interlock or ventilation system. The Code's examples include machine guards and confined space ventilation (Appendix C).
Administrative controls
Administrative controls: rules and procedures that change how people work. They include safe work procedures (SWPs), permit-to-work systems, training and what the Code calls "scheduling of incompatible works", such as keeping hot work away from a solvent cleaning job. The Code says they work "by adherence to procedures or instructions" (Appendix C), so they depend on people following them.
Permit-to-work: a written system for authorising specific higher-risk work, such as hot work, before it starts, with the precautions spelt out. The Regulations count it as an administrative control (regulation 4(5)).
Personal protective equipment
PPE: equipment the worker wears, such as safety helmets, gloves, eye protection, earplugs or a harness. The WSH Council's risk assessment guidance says PPE "should be explored only after upstream risk controls have been considered, as a short-term contingency during emergency, maintenance, repair or as an additional protective measure against residual risks." It adds that "the effectiveness of PPE depends greatly on whether it is chosen and fitted correctly, worn at all times and maintained properly." For a fuller explanation, see what counts as PPE.
Residual risk: in the Code's words, "the remaining risks after implementation of risk controls" (Appendix E).
Use more than one control
The levels aren't a menu where you pick one. Section 6.6.2.3 of the Code says controls "are not to be taken as isolated or single solutions. Generally, it is more effective to use a combination of control measures." Its example: "engineering controls work better with administrative controls like training and SWPs."
Hierarchy of controls examples from Singapore workplaces
These hierarchy of controls examples show how one hazard can be tackled at every level. They're illustrative only; the heat stress row uses MOM's listed measures, grouped by us. Your own risk assessment decides what's reasonably practicable on your site.
| Hazard | Elimination / substitution | Engineering | Administrative | PPE / clothing |
|---|---|---|---|---|
| Heat stress (outdoor work) | Not usually practicable for outdoor work | Shaded rest areas; cool rest and work areas with fans or air coolers | Reschedule outdoor physical work to cooler parts of the day where feasible; hourly WBGT monitoring; rest breaks under shade; cool drinking water; acclimatisation; heat stress training | Suitable clothing (loose-fitting, light-coloured) |
| Working at height | Assemble at ground level | Guardrails, scaffolds | Permit-to-work, training | Full-body harness |
| Noise | Quieter equipment | Enclosures, barriers | Scheduling, signage | Earplugs, earmuffs |
| Chemical cleaning | Less hazardous product | Local exhaust ventilation | SWPs, training | Chemical-resistant gloves, eye protection |
| Dust | Wet methods instead of dry cutting | Extraction | Housekeeping | Respirator |
The heat stress row follows MOM's heat stress measures for outdoor work. These include rescheduling outdoor work to cooler parts of the day, rest under shade, cool rest areas with fans, cool drinking water, acclimatisation, hourly WBGT monitoring, heat stress training and loose-fitting, light-coloured clothing.
WBGT (wet bulb globe temperature): the heat stress indicator MOM uses to set its measures. Besides air temperature, it's affected by humidity, wind speed and solar radiation (MOM WBGT monitoring guidelines). For more, see our guide to heat stress management.

Illustrative image only. Not a RigArmor product, customer or site.
Why PPE and workwear come last (and still matter)
PPE and clothing come last because they protect only the person wearing them, only when worn correctly and only against the hazard they're made for. The hazard is still there. If a glove tears or a harness isn't anchored, the protection is gone. The Code gives a similar harness example of residual risk (Appendix E).
That doesn't make the bottom level useless. It often covers what's left after the other controls. It just shouldn't be the only one.
Clothing gets lumped together, so it helps to separate three things:
- General work coveralls protect skin and clothes from dirt, grease and wear. They aren't certified PPE.
- High-visibility garments are designed to make the wearer easier to see. If your site requires them, check which standard it specifies.
- Flame-resistant (FR) garments are a different kind of clothing, for sites with flame, arc-flash or hot-work hazards. Check them against the standard your site specifies.
Our 100% cotton coveralls (175 gsm or heavy-duty 270 gsm, plain woven) are general workwear, not flame-resistant. They aren't suitable for sites that require flame-resistant clothing, such as PETRONAS sites. They aren't certified PPE, and they aren't a control for fire, chemical or visibility hazards. The reflective tape helps people see the wearer, but the coverall isn't a rated high-visibility garment. See our page on high-visibility workwear for what to check if your site requires it. If your risk assessment calls for general workwear only, see our cotton work coveralls.
How to apply the hierarchy in a risk assessment
Work through it in five steps:
- Identify the hazard. List each work activity and what could cause harm.
- Evaluate the risk. Rate how severe and how likely harm is, taking existing controls into account. The Code recommends a 5x5 risk matrix but doesn't restrict you to it.
- Work down the hierarchy. First, ask whether you can eliminate the hazard. If not, try substitution, then engineering, then administrative controls, then PPE. For extra controls, the Code says those "higher up in the Hierarchy of Control should be considered first" (section 6.6.3.2).
- Combine controls. Pair engineering controls with training and SWPs. Note any residual risk and what covers it.
- Review. The Code and the Regulations require a review at least once every three years. You also need to review after anyone is injured by a workplace hazard, or after a significant change in work practices or procedures. The Code suggests an annual review where practicable. Risk assessment records must be kept for at least three years.
Working in Malaysia, Indonesia or the Philippines? The rules there differ from Singapore's, so check local requirements or ask your WSH officer.
FAQ
What is the hierarchy of controls?
The hierarchy of controls is an order for reducing workplace risk, from most to least effective: elimination, substitution, engineering controls, administrative controls and PPE. In Singapore, the WSH Council's Code of Practice on WSH Risk Management calls it the "Hierarchy of Control". It asks employers to consider the levels in that order.
What are the 5 levels of the hierarchy of control?
The 5 levels are elimination (remove the hazard), substitution (use something less hazardous), engineering controls (physical changes such as guards or ventilation), administrative controls (procedures, permits and training) and personal protective equipment. Controls higher up are often more effective because they reduce the risk at or close to the source.
Why is PPE the last level?
PPE protects only the person wearing it, and the hazard stays in place. The WSH Council says its effectiveness "depends greatly on whether it is chosen and fitted correctly, worn at all times and maintained properly." So it's used after upstream controls are considered, as a short-term contingency, or against residual risk.
What is the difference between engineering and administrative controls?
Engineering controls change the workplace or equipment, such as a machine guard, an enclosure or local exhaust ventilation. Administrative controls change how people work, such as safe work procedures, permit-to-work systems, training or scheduling. NIOSH says engineering controls are more effective because they control exposures "without significant human interaction".
Can you use more than one control at once?
Yes. Section 6.6.2.3 of the Code of Practice says: "Generally, it is more effective to use a combination of control measures." Its example is engineering controls working better with administrative controls like training and safe work procedures. PPE can then cover any residual risk.
What is an example of the hierarchy of controls for heat stress?
For outdoor heat, you might reschedule heavy work to cooler parts of the day and provide shaded and cooled rest areas with fans. Then add rest breaks, cool drinking water, acclimatisation and WBGT monitoring. Suitable loose-fitting, light-coloured clothing comes last. MOM's heat stress measures for outdoor work set out the details.
In short
Work down the hierarchy of controls in order: eliminate, substitute, engineer, then administer. Combine controls rather than relying on one. PPE and workwear come last. They still matter, but only for the hazards they're made for.
This guide is general information, not legal or safety advice, and not a substitute for your site's risk assessment. Check your site's WSH requirements with your WSH officer.
Questions about our coveralls? Email sales@rigarmor.com.